« Older Entries
Newer Entries »

“Blank” wine

Posted November 19, 2016 By Landis V

Ran across the idea for a “blank” wine here (#14) and thought it was a great thing to hold on to for topping off and the like.

  • Juice of 1 lemon
  • Teabag steeped in a cup of water until cold
  • Handful of raisins
  • 2 lbs sugar
  • 1 gallon water

The author notes that it has very little flavor of its own, but has enough acid, tannin, and body to blend well with just about anything.

Be the first to comment
Filed in Food and Drink | Tagged:
   

Useful/relevant Arduino tutorial for programming an ATTiny85

Posted October 31, 2016 By Landis V

Bought an Arduino kit recently and have done just a little bit with it, but not much.  One of the projects I’m looking at uses an ATTiny85 to reduce CPU for a 433MHz receiver (https://github.com/pilight/pilight_firmware), so I bought some ATTiny85’s and will need to program them.  That can be done using Arduino 1.6 – reference article here.

Be the first to comment
Filed in DIY, Electronics, Hobby Engineering, Links | Tagged: ,
   

Remote power switches for rebooting cablemodem and router

Posted August 20, 2016 By Landis V

I hate it when I’m away from home and either the ISP or some of my equipment glitches, necessitating a reboot or two.  I have enough systems in place that I should be able to automate this process.  To do so, I need to get some remotely controllable equipment, create the state diagram (not good if I power cycle one of the network components required to reach the remote switch and it doesn’t come back up!), and write the scripts to run the logic.

I’d also like to have easily accessible power switches in my data closet so I can power cycle the devices without having to pull them down and unplug the power from the back of them.

Hardware components I’ve looked at

SainSmart 16 channel web relay – at Amazon.  This could work if installed between the transformer block and the switches.

Ethernet relay on eBay, claims to be AC250V @ 10A, though that would probably be pushing it.  Would have to look up the specs on the relays they used.  For the watt draw on the AC, depending upon the size, might be able to install it inside a large surge protector housing and wire the outlets through it.

Controllable Four Outlet Power Relay Module – at Adafruit.  Not network connected, and would require some other device to control it.  But most likely UL listed and designed to handle AC.

Ended up finding a Digital Loggers LPC-3 on eBay for $57 shipped that should do the job nicely.  Manual is here.

Be the first to comment
Filed in DIY, Electronics, Energy, Links, Monitoring, Networking, Projects, Purchases
   

More 434MHz stuff to look at later

Posted August 20, 2016 By Landis V

Acurite #0899 self emptying rain gauge – at Amazon

Blog post on reversing the signal from Acurite temperature sensors; may be similar for the rain gauges.  Also mentions the RTL SDR.  Probably wouldn’t be bad to have.

Another blog post regarding reading the Acurite 5n1 station.  Possible that part of this will already cover the rain gauge.  Also discusses SDR and mentions the rtl_433 tool.

This blog post looks like rtl_433 supports the Acurite 896 decode natively, so if the protocol is similar or the same it may be simple.

RTL Software Defined Radio – at Amazon – seems like it’s probably a decent model, some good reviews.  Looks like there’s a little more to it than just “buy this and set up the software”.

Bought a cheap receiver off of eBay from Hong Kong for $7.31 (original listing).

Also, here was an Instructable about making a cheap combination RF/Bluetooth/433 MHz remote using an Arduino.

Additional Links

Be the first to comment
Filed in Communications, DIY, Electronics, Hacks, Links, Linux, Monitoring, Projects, Raspberry Pi, Software, To Buy, Wireless | Tagged: , ,
   

Stellar garage organization

Posted July 3, 2016 By Landis V

This guy has the best garage organization I have ever seen.  Definitely will be taking some ideas from this page for tool and garage organization.

http://www.garagejournal.com/forum/showthread.php?t=174553&showall=1

Be the first to comment
Filed in Fabrication, Hobby Engineering, Home, Links, Projects, To Buy | Tagged:
   

On Networks N150R Routers

Posted June 13, 2016 By Landis V

Picked up a couple of these from Newegg for free plus a couple of bucks shipping after rebate.  Figured that in combination with a couple of relays on the GPIOs, I could probably use them for switches or work with the serial port for a sensor connection.  Just a few notes on them.

OpenWRT 15.05 Chaos Calmer patched to expose the GPIOs:  https://micu.webserwer.pl/pmwiki/pmwiki.php?n=OpenWRT.Downloads

Forum thread on not flashing direct to 15.05.1; I went to 14.07, then to 15.05.  https://forum.openwrt.org/viewtopic.php?id=51576

OpenWRT Wiki page with device info including GPIOs https://wiki.openwrt.org/toh/netgear/wnr612v2

Controlling the GPIOs

From here, the simple way to control the GPIOs natively is with the “brightness” value for the LEDs.  By example for the LAN1 LED (others are in the same path):

root@OpenWrt:~# echo 0 > /sys/class/leds/netgear\:green\:lan1/brightness
root@OpenWrt:~# echo 1 > /sys/class/leds/netgear\:green\:lan1/brightness

Update 9/18/2016

Finally got the LAN2 LED peeled off of the board, had a heck of a time with it.  After doing so, I discovered that I only get ~2.5v across the pins when the GPIO is active… not enough to drive my 3.3v relays.  I assume they are probably using a voltage divider here.  Measuring the resistance between the positive and negative ends of the LED without power applied, I get about 1580 ohms one direction, and 670 in the other.  There appears to be a ~960 ohm resistor at CA111, but I haven’t figured out exactly how this ties in.

Update 10/9/2016

Spent some time with this again over the past couple of days.  I removed the resistor at CA111, but apparently it is not a divider.  May need to spend some time to see if I can make something work with a 2N7000 MOSFET or something like that, but I’m pretty novice so that will take some effort.

I did test out my 433MHz ASK receiver on the TTL serial port, but without much luck.  This OpenWRT page was helpful in getting stty installed and setting the baud rate on the serial port,

‘stty -F /dev/ttyS0 9600 clocal cread cs8 -cstopb -parenb’ to set the config, and
‘stty -F /dev/ttyS0 -a’ to verify the config

but still didn’t get any output.  I’ll have to give it a shot with my Raspberry Pi just to see if I can get anything out of there.

Be the first to comment
Filed in Electronics, Hacks, Links, Linux, Networking, Purchases | Tagged:
   

Maverick/Ivation 434MHz BBQ Thermometer Receiver for Raspberry Pi

Posted May 28, 2016 By Landis V

Purpose

I recently purchased an Ivation barbecue thermometer which is supposed to be a pretty decent similar build to the Maverick 733 (I believe).  Of course, one of the first things that comes to mind is how to tie this in to some type of IP connected system so I don’t have to rely upon the included receiver and its limited range, and can instead take advantage of wifi, Internet, and the smartphone I always have with me.  Turns out it should be pretty feasible in conjunction with the Raspberry Pi I already have plans to set up as a sort of garage controller.  That device will be connected by ethernet and will have a constant and reasonably close proximity to my smoker and grills already.  This post is for my notes on links that will be useful when (if?) I actually get around to making this work.

Software/code links and notes will come later, after I actually get the equipment to start testing.

About the BBQ thermometers

The Maverick (and presumably Ivation) transmit on the 433.92MHz frequency using OOK.  The Hackaday link to Bob Blake’s article below describes the communications protocols and encoding.

Links

 

Update 10/9/16

Spent some time trying to get this working with my On Networks N150R over the past couple of days without much luck.  May have to give it a try with one of my Raspberry Pi’s and see if I can get it working there, if for no other reason than to verify that the receiver module I purchased is functional and/or that I have it wired somewhat properly.

Be the first to comment
Filed in DIY, Food and Drink, Hacks, Internet, Links, Linux, Networking, Raspberry Pi
   
« Older Entries
Newer Entries »